Intellibox® IR Cat No. 65 050 (Available Nov 08). Intellibox-IR is the ultimate for all who would like to continue using old Motorola or DCC devices, Selectrix decoders, have their layout controlled, s88-feedback or want to switch routes. Infrared Receiver The Intellibox-IR has an integrated infrared receiver, so that the IRIS remote control can be used directly (for Intelliboxes with Part No. 650 or 65000 the IRIS set Part No. 66500 can be used as remote control and receiver). Virtual Locomotive Addresses In addition to the fixed locomotive address, any address with a maximum of four digits can be assigned to a locomotive. Vehicles can be called up by their operating address or sequence number.
Multi-traction (Consist) 8 combinations with up to 4 locomotives per consist can be administered by the Intellibox. The entire consist is controlled with one speed control under the address of the first locomotive. Feedback Monitor The Intellibox-IR can not only evaluate LocoNet feedbacks, but also a maximum of 31 s88-feedback modules. The status of track sections can then be read directly from the Intellibox display. Route control The Intellibox route control can administer up to 48 routes. Each route can contain up to 10 switching processes. Because an activated route can contain another route the flexibility of the routes can be extended. Interface The serial (V.24, RS232) computer interface, with a maximum data rate of 19200 Baud, input buffer and an extended command set, is a fast connection to the PC or MAC. Suitable software must support the Intellibox protocol (P50x).
Compatibility: The Intellibox-IR can be combined with the many varied digital components from other manufacturers. Motorola format boosters from Märklin DCC format boosters from, for example, Lenz, LGB, Arnold Arnold booster, new (86015) s88 feedback modules from Märklin, Viessmann... LocoNet feedback modules from Digitrax Control 80, 80f, IR from Märklin and Arnold Control unit as speed controller and turnout booster Central unit as turnout booster Keyboard, Memory from Märklin and Arnold Switch board from Märklin and s.e.s LokMaus 1 from Roco and LGB Roco® LokMaus 2® and multiMaus with Maus Adapter All devices with LocoNet interface PC or MAC using serial interface IntelliBox IR Accessories: 20 070 70VA transformer 60 500 Manual with demo program 61 010 PC interface cable 61 020 Adapter Intellibox/Control- or Central-Unit 61 030 Adapter Intellibox/ Märklin DC Booster 61 040 Connector set (1 x 3 way, 1 x 6 way) 65 020 Upgrade Software 2.0 66 510 Infrared control IRIS 66 520 Infrared receiver extender 66 530 Y-cable for LokMaus socket COMPARE INTELLIBOXES
Intellibox Upgrade Software 2.0 - Cat No. 65 020 (Extension of the Intellibox system software.) The Upgrade 2.0 is an extension for all Intelliboxes that were supplied with system software version lower than 2.0. Upgrade 2.0 adds the following new functionality: 10000 Loco Special functions With appropriate DCC decoders special functions f1 to f9999 can be accessed. Locomotive selection from the Dispatch Buffer The Dispatch buffer contains all of the locomotive addresses which are currently under control by the Intellibox. The new software makes a selection list of these addresses available and the desired locomotive can be selected from this list directly. Loco Find Function As soon as a locomotive with DCC decoder is placed on the programming track the locomotive address is automatically read from the decoder and passed to a speed controller. Reload the displayed locomotive addresses The locomotive addresses shown in the Intellibox display when it is switched off are stored and are immediately available the next time it is turned back on without the annoying re-entry. LISSY Mode Each LISSY receiver can be monitored with the Intellibox. If a locomotive with LISSY transmitter is recognized the centre of the Intellibox the display shows the locomotive address. DirectDrive With the push of a button, control of the locomotive which passed a particular LISSY receiver can be taken over by a speed controller without inputting the address or name of the locomotive. Route Control For all devices without route control this system software will provide up to 48 routes. The Upgrade software is available on the Internet free of charge for owners of the Intellibox-IR. For older devices the software can be purchased.

IRIS - The Infrared Intellibox Controller. - Cat. No. 66 500 Direct control of up to 4 locomotives. Address range 1-9999. Special functions: function and F1 to F12. Changes turnouts in address range 1 to 2048. Activates routes which are stored in the Intellibox. Supports all speed step (14-128 drive positions). With 4 different channels, i.e. each Intellibox has 4 channels. External Receiver with 5m cable The infrared Intellibox control IRIS extends the Intellibox with an interior use wireless remote control with a range of up to 10m. With IRIS all locomotives on the digital layout can be selected and control its driving direction, speed, and special functions. IRIS can switch all solenoids and select all routes which are stored in the Intellibox.

Remote Control IRIS uses 4 different transmission channels, which can be selected with the A, B, C or D keys for controlling the Intellibox. Each transmission channel can select a locomotive address for control, fully independent of the other channels. Furthermore each channel can have different solenoid device addresses assigned to the solenoid device keys. The addresses selected for each channel are stored in the Intellibox non-volatile memory and are therefore available after turning the power off and on. If only one remote control is used, then the channel can be quickly changed with the help of the keys, between 4 locomotives or 4 groups of 4 solenoids. If several remote controls are used, then each person can control a locomotive using a transmission channel, without affecting the locomotives of the others that are on different transmission channels. The remote control has 4 different channels which makes it possible to use 4 transmitters in an area. Important: To use IRIS with the Intellibox it must have system software Version 1.5 or higher. IRIS Receiver External receivers can be connected via their 5m long cable at any location in the area. If more than one receiver is required in certain spatial arrangements three additional external infrared receivers (66 520) can be connected in parallel with the first receiver via a Y- cable. The IRIS set contains the remote control, a receiver, a manual, batteries. Note: The Intellibox-IR (65 050) has an integrated infrared receiver, so that the IRIS remote control can be used directly. Intelliboxes with the Cat Nos. 650 or 65 000 require the IRIS remote control and an external receiver. It is not possible to connect an infrared receiver to the Intellibox Basic. 66 500 IRIS set 66 510 IRIS Remote control 66 520 External IR receiver 66 530 Y-cables

FRED-CS - The hand control especially for the central station. - Cat. No. 66 010 Direct connection to the central station Low friction rotary control Single hand operation Switches light and up to 14 special functions Large working radius Suitably matching the Design of Central Station, the hand control has a large rotary speed control with end stop. This is very precise and low friction. It has a handing feel which you are undoubtedly looking for in Märklin devices. It is ideal when shunting. With the FRED-CS in one hand one can drive "blind" and observe the locomotive from close proximity. One hand remains free for coupling or loading activities. With the 3m long spiral cable you have a large working radius. A rocker switch changes the driving direction, so you can sense this at any time and are not dependent on the LED display. The stop key is the emergency brake for the currently controlled locomotive. The function keys can switch light and up to 14 special functions. The locomotive to be controlled is assigned to the FRED-CS from the Central Station. Up to 31 FRED-CS can be attached to a Central station. Supplied is a 3m spiral lead. (Available now).

Advance Notice - 2009 Intellibox II - The next generation. The successor to the legendary Intellibox IR which in one decade became the reference for all digital centers, will come in a whole new version next Year. Tailored for the model railroader who wants to run a railway and not play with a computer. Technically, the Intellibox II is a completely new device. Only the proven ergonomics remains. For us it is a given that it is compatible with our other devices.

The most obvious innovation is the large easy-to-read display. The various parameters are shown in plain text and as function symbols. The information is very detailed and also easy to read from the side. The additional keys on the right and left of the display are contextually assigned, for ast access to menu options and functions. The speed display is not only in speed steps or percent, but now also in km/h. Up to 32768 special functions per locomotive are available. A large locomotive database with the text display of locomotive names can be set individually. New also is decoder programming in plain text, the detailed help function, a model clock and computer connection via the USB port. Because of the new low power technology the heat development is greatly reduced and the heat sink is no longer required. New features Large, high resolution display with backlighting Informative display Detailed representation, therefore very readable Information in plain text or as function symbols All keys with backlighting Context sensitive key allocation Speed indication also in km/h Up to 32768 switchable functions per locomotive Large locomotive data base Input of locomotive names Decoder programming in plain text Routes callable by feedback contacts Help function Model time clock USB computer interface Low power technology Familiar functionality Data format DCC, Motorola Up to 128 speed steps Up to 9999 decoder addresses Virtual locomotive addresses Multiple traction (consist) DirectDrive function Switching of turnouts, signals and routes Integrated Infrared receiver Connections for LocoNet, transformer, track, programming track, Booster, DCC booster and additional Infrared receiver Still: Everything in a box With the Intellibox II you are completely equipped for digital operation. The Intellibox II can operate on 2-and 3-Rail layouts. It supports 128 speed steps and 9999 decoder addresses, Locomotive, function, turnout and switching decoders in the Motorola and DCC format from different manufacturers at the same time. A single device puts the following components of Digital systems at your disposal: Central processing unit, booster, Speed controller, key board, Programmer, interface, feedback mode, route control and LISSY Mode with the DirectDrive function. The integrated Infrared receiver makes the direct use of an IRIS infrared remote control possible. As bus system the Intellibox II uses the model railway network work LocoNet. The data communication is reliable and fast. Accessories can be connected to the layout easily and quickly. The connection of the individual locomotive control system LISSY makes automation of the model railway possible without the need for a computer. With the DirectDrive function a locomotive which passed a selected LISSY receiver can be taken over on a speed controller by the push of a button, without the input of locomotive address or name. The integrated USB interface provides a fast connection to PC or MAC. Any software that supports the LocoNet protocol can be used for automated layout control. For more information from All Aboard Modellbahn about Ühlenbrock send for a Brochure or download a 2008 CATALOGUE here. For your nearest reseller see Retail Outlets. For a Price List click here. For Trade Enquiries about Ühlenbrock from All Aboard Modellbahn please go to our Trade Enquiries page. Click here to see Uhlenbrock Elektronik's website.   Uhlenbrock Home Page > Intellibox > IntelliSound > LocoNet > IntelliDrive > IntelliLight > Track-Control > Digital Servos